How to anchor a boat securely is one of the most basic skills in boat handling. Learn how to anchor a boat right, with control and confidence; and we will all sleep easier. Anchoring poorly endangers not only your boat, but also the other boats anchored nearby. So, even if your anchoring technique is good, it is wise to review these tips.
If your anchors for boats has not set securely or you have anchored on foul ground, there is a high chance of theanchors for boats dragging. Even when this happens, an Anchor Buddy weight will give the anchor another chance to dig in as it keeps the chain on the seabed.
How to Anchor a Boat | Anchors for Boats
A boat’s primary ground tackle – anchors, chain, warp and shackles, must be of a size considered adequate for the size and weight of your vessel. (Check with the manufacturer’s recommendations). To maximize holding power, anchors for boats need to have some sturdy galvanized chain between it and the anchor line, no less than 4.5m – 6m (15-20ft). It should be at least the length of the vessel. The warp or chain if all-chain is used should run free in the anchor locker and the bitter end should be fastened to the vessel. It is a good idea to have the warp or chain marked off in 3m – 6m (10-15ft) increments to be sure how much is being let out, when anchoring.
How to Anchor a Boat | Basic Anchoring Requirements
When nearing an anchorage, shorten up the painter if you are towing a dinghy, so it cannot possibly reach the propeller when backing the vessel. Make sure crew members know what is expected of them. Remember, it is almost impossible to hear commands from the bow in the cockpit, so a few simple hand signals should be established.
Once in the bay, consider how the boats already there are anchored. Most will be swinging on single anchors for boats warp. But in heavy weather, some may be using an anchor weight; some may have two anchors for boats set off the bow, or one off the bow and one set astern. Some may be on permanent moorings. When the wind or current shifts, the vessel with an anchor weight or two bow anchors set, will swing in a shorter radius than boats on a single anchor. Vessels anchored fore and aft won’t swing at all. Those on permanent moorings will pivot around their bows, but move very little. In very light air, boats with all chain anchoring systems may not swing as far or as quickly as those riding a mostly nylon warp.
As the newest arrival, how to anchor a boat correctly is to keep clear of boats already there. Make sure you allow for any change in wind direction and strength. It is always safer to leave extra space around your boat.
Position your boat with the bow to the wind (or the current, if that is stronger), roughly equidistant from your nearest neighbors in the approximate location you wish to be in when anchored. Make sure you will have ample water beneath you at dead low tide.
In normal conditions, a safe minimum scope ratio is 5 to 1 (warp or chain length to depth). In heavy weather 7 to 1 or more. Depth is the depth of water at high tide, plus the height from water line to the bow roller. Scope is the actual amount of anchor line paid out when the boat is safely anchored. For example, if high water is 20ft deep and your bow roller is 5ft above the water, you need 125ft (i.e. 5 times 20 + 5ft) of scope to anchor.
Remember, putting out too little scope is one of the most common mistakes a skipper makes; so this is not an example of how to anchor a boat.
While still hovering above the spot where you intend to lower your anchors for boats, take another look around your boat. Don’t set it to close alongside or close off the bows of other vessels. If you do, you may well swing into them if there is a wind shift. It is usually safe to set more close astern or off the quarter of another boat. Look also at the direction in which the warps and chains of nearby boats are pointing. A boat may have a second anchors for boats set off in your direction, which you may foul if your anchor drops on top.
How to anchor a boat in light winds | Don’t assume that everyone’s anchor is positioned straight out before the bow. In calm conditions it may warp, especially chains, may be stretched out in the direction the last real breeze blew from. You can always ask the skipper of a nearby boat where his lies.
If all is well, circle back around to your intended final resting spot and then slowly coast forward the approximate distance of your planned scope. Stop the vessel completely with a short burst of reverse power. When your vessel has lost all way and is at a complete halt, lower the anchor. If you have any way on at all, your chain will drag over the anchors for boats, once the boat drops back and may foul the anchor.
When you let go, don’t let the chain and warp go screaming out to pile on itself. Instead, lower the anchor quickly, paying out the warp or chain hand over hand or with the windlass, until you feel it rest on the seabed. Signal to the helmsperson to put the engine in very slow reverse, so the vessel just begins to make slight stern-way about the time the anchor touches the bottom. If it is windy, leave the engine in neutral and let the boat’s windage and motion provide the backing propulsion. As the boat continues to back slowly, also feed out the line (be it warp or all chain) slowly, maintaining a slight tension on it, so that it is laying out straight on the seabed, instead of in a pile.
With the boat still backing slowly and with about half of the scope out, hold the line firmly until you feel the slack is taken up and the anchor is tugging. Feed more line out, but keep tension on so the anchors for boats is being set straight. This is the correct way of how to anchor a boat.
Pass the line around the bollard to make it easier to hold. Snub up firmly, just long enough to feel it tugging for a second, then ease off. Repeat this snub and feed pattern several times. On a larger vessel, with an all chain line and heavy ground tackle, you would be using the windlass gypsy for this task, alternatively braking and releasing the drum.
This gentle snubbing/feeding action while backing down the boat is the surest way of how to anchor a boat. Yet it is a technique very few skippers seem to employ. It gives an opportunity to right itself, penetrate the bottom surface and gradually dig in.
If the anchors for boats has taken hold, the boat will come to an abrupt halt, firmly setting the anchor. However as we all know, there are times when you do worry whether it is holding. It can roll out and dislodge in vicious wind gusts and squalls or very strong wind and when your boat is swinging wildly. These conditions are often unexpected and are cause for concern.
How to Anchor a Boat | Why anchors drag and what you can do to reduce the risk.
Reports from boats that have faced whole gale to cyclone winds at anchor, say that it is not the winds that break anchor gear and upset anchors, but the accompanying wave action which causes boats to pitch, surge, heave and yaw. Surge is the worst of these motions as the boat rides over the waves alternately stretching and relaxing the anchor warp like a horizontal yo-yo. Surging of the boat sometimes as much as doubles the loads felt from wind drag alone. The surge factor can be proportioned to the boat displacement and length. Surge is the motion forward and backward in the direction of boat travel, along the longitudinal axis.
The other 5 motions experienced by a boat at anchor are sway, heave, roll, pitch and yaw. The wind tends to create yawing and swaying, the waves tend to create pitching and heaving, while the anchor restraint, depending on its elasticity, is involved with surging.
Read the Royal Navy’s test on why anchors drag “…if the angle of pull is 10 degrees off the seabed, the anchor’s maximum holding power is down to 60%. At 15 degrees, it is further reduced to only 40% of its maximum holding power“.